Jerry Hill Steadicam Products

Jerry Hill Steadicam Products

Jerry Hill Steadicam Products

VIEW CART

PAM to Heden Motors Adapter

By Leave a Comment 0

This adapter allows you to use the Pam motor brackets with the Heden and Arri motors. Heden motor’s model M26VE, M21VE, M21VE-L. Arriflex motor’s model CLM-2,3,4. This is a 19mm shaft and a rosette on one side. The adapter can be flipped over easily in the field. The shaft is 19mm, so no need for reducers.

Just insert the rosette into your iris rod clamp and position and secure it.This will mate to the normal D-clamps and Pam offset. If you are currently using my system, all you will require is the adapter.

Arri SR-3 Iris Mount

By Leave a Comment 0

Accessory Iris rod mount for the above (SR-3) bracket. This will enable you to use the Hill square to round iris rod’s. Supplied with all mounting screws. (Anodized Purple)…(Rods are not included with SR3IrisMt.)

Square to Round Rods

By Leave a Comment 0

These are different length rods for use with the #H2-N-1, #HP, #HLMB, #SR3LMB, #SR3IVS, #AIRC. All rods are 15mm in diameter for motor placement. Lengths Available: 3.5″, 5″, 7″ inch lengths.

PMM-15-Rosette

By Leave a Comment 0

This adapter is to be used with the Rodriguez Pana bracket. His bracket mounts onto the Panavision Modular mount.
This interfaces my PAM Rosette system to his bracket allowing rotation and a little adjustment in and out of the motor.PMM15mm

 

Part #PMM-15-Rosette     Weight:  .03 oz       $40.00

Arri Iris Rod Clamp

By Leave a Comment 0

This allows you to add an iris rod quick and easy. This Iris rod clamp inserts into the Arri dovetails. It works in combination with the Hill square to round rods. The clamp has two slots in the top of it for the rods to run horizontal or vertical (Depending on the camera). This will work on the following Arriflex camera’s 535, 435, 35-3, SR-3, and any other cameras that have been modified with the Arri dovetail. The AIRC can be purchased alone by itself for those who own the rods already, and also with a rod as a kit. Comes as you see in the picture to the left.

Moviecam Compact/SL Iris stud

By Leave a Comment 0

Iris Pull? This spud takes seconds to put on a moviecam body. There is a small dovetail on the face of the camera, next to the lens. This simply slides onto that dovetail and a finger knob secures it. This can be used as a primary focus motor spud or a quick addition in the case of an Iris pull. Will work with both Compact and SL Bodies. The stud is (15mm) 2 ½” long and is Anodized Gray.

Arm Post Clamp

By Leave a Comment 0

Arm post clamp for 5/8″ post (Pro, 3-A, EFP) and 3/4″ post (Tiffen) with thrust bearing.

Anodized Blue.

15mm Round Rods

By Leave a Comment 0

These are different length 15mm Iris rods for use with the Dog bone, Lateral Mount or stand alone.  Lengths Available: 3.5″, 6″,  9″ inch.

Adjustable Lever for Pam Arm’s

By Leave a Comment 0

Replacement adjustable Levers for standard PAM arm’s , Uni-Clamp, Hill Balance Bracket (HBB) and Magdock.

Note: If you have the Uni-Clamp arms with the Butterfly knob and stud and would like to switch to the Kipp handles. Machining is required! Drill and tap!