Jerry Hill Steadicam Products
19160 Arminta Street
Reseda, Ca. 91335-1105
Phone: (818) 772-9256 - Fax: (818) 772-9251
E-Mail: jerry@steadimoves.com

Store Hours: Monday thru Friday, 9 am to 6 pm - PST

Hill Products Description

Inclomonitor

The Inclomonitor is an innovative new device produced by a consortium of three companies jointly having over forty years experience in the film and television industry. The Inclomonitor is mounted onto a Crane Arm, Jib Arm, Jimmy Jib or Steadicam rig and a LCD monitor attached to the integral bracket. As the Crane Arm is jibbed up and down, the LCD mounting bracket is driven by a servo motor inside the unit. The result is that the viewing angle is kept constant and the operator does not have to move to see the image. The Inclomonitor is a completely stand alone unit and only requires a DC power source of 12 - 30V to operate.
There are controls to adjust the angle that the monitor is driven to at the extreme of the Crane Arm travel; a position control to manually drive the monitor to any desired position; and a reset control to position the monitor in the vertical plane.

The Inclomonitor package includes the following items. Inclomonitor Servo, L-Bracket, Cable Loom, Magic Arm, and Instructions.

Inclomonitor package sold as above.

Part# IncloM

$1250.00

(Monitor pictured is not included.)

(Customer must provide there own power connector end on cable loom.)

Uni-Clamp

Arri 435 Low Mode Bracket

This is a low mode bracket that has all the features that we have needed.
This bracket will enable the operator to preset the camera tilt angle.
You will be able to adjust it up or down to about a 30-degree angle (see photo). There is an additional bracket (Iris rod) that mounts on the side of the body to mount a motor. The top plate will have an adjustment from side to side of 3" inches. The top plate has meshed 3/8"-16 and 1/4"-20 tapped holes for your sled dovetail. It also can be turned around (cantilevered for side to side) and cantilevered fore and aft.
Small in size to reduce weight, but sturdy to add support to the dovetails.

The new design folds small to save space in your case.

Kit contains: bracket, iris rod mount,allen tool, and net pouch.

(Hard anodized gray to match camera)

Part #H435LMB

Weight: 13 oz.

$575.00

Arri SR-3 Low Mode Bracket

This is a low mode bracket is for the SR-3 only. This mounts to the top of the handle with a 3/8-16 screw (Supplied) and to the photo shoe that is located on front. This clears the way for the color taps and after market side taps to be used. Easy and quick to install. (Anodized Purple)
(Below) An optional motor rod adapter.

Part #SR3LMB

Weight: 4 oz.

$350.00

Arri SR-3 Iris Mount

Accessory Iris rod mount for the above (SR-3) bracket.
This will enable you to use the Hill square to round iris rod's. Supplied with all mounting screws.

(Anodized Purple).........(Rods are not included with SR3IrisMt.)

Part #SR3IrisMt

Weight: 1.62 oz

$75.00

Arri SR-3 IVS - Low Mode Bracket

This low mode bracket is specifically made for the Arri SR-3 IVS model camera body. Like the lmb picture above. This mounts to the top of the handle with two 3/8-16 screws.(Supplied) The screws are captive so they stay with the bracket at all times. The IVS model camera does not have the photo shoe on the front of the handle. However this bracket will still allow for the Iris mount to be used. (Above) This bracket was designed with the assistance of Clairmont camera. (Anodized Purple)

Part #SR3IVS-LMB

Weight: 4 oz.

$300.00

Gorelock 1 & 2

The Gorelock1 has been brought back by popular demand. This will work with the 1.580" and 1.500" post, or the Pro and the Master sled post sizes. The GAD1 and the GAD2 have the same features. The GAD1 has a smaller diameter fork and will only accept the 1.580" and 1.500"O.D. docking rings. If you have a Pro sled with a 1.500" post size and think you will be upgrading to a 2" post in the future, I would suggest buying the GAD2. that way you will only need to purchase a diffrent size docking ring and the fork will work. Also re-introduced for the Mag-Dock. This will intergrate into what you already are using.

The GAD2 upgrades the GAD1. This accomdates the all the post sizes.As before the same great features are still intergraded. The key features are, no aircraft pin, automatically locks the sled in place, securely holds the sled from flopping from side to side when changing magazines or lenses, the docking ring can be positioned right under the top stage, the post never touches the fork when docking, the Gorelock2 has a built in 2 degree angle, the sled can be rotated in the fork for adjustments, red release levers are on both sides for ambidextrous operation, two handed control on the sled when mounting and dismounting. The new features are; now accepts the largest to smallest post size, starting with the MK-V 2" 4 stage post size of 2.125", 2.00", 1.860", 1.790", 1.685", 1.580", and the 1.500" The O.D. of all the rings are the same size. Also the the docking rings have been changed to a larger clamping screw.

When Ordering!

There are seven different post sizes out there. Too many sizes to list here (above) and there may be more that I do not know about. When ordering, I have to know your post size and the location of where the docking ring is going to be placed. This will enable me to fill your needs and cut down on the confusion.
When ordering with the Hill Docking Bracket, I need to know what arm post size you are using to provide the proper balance stud size. (Example: 3-A and Pro are 5/8" dia. and Master is 19mm dia.) Below are a few examples of the part numbers and pricing. If you do not see your size of post please call and inquire. The DR2 will not interchange with the old Gorelock.(GAD1)

Old Style (Model 1) ( order this for post size 1.580" and smaller, never upgrading to a bigger post size )

Part# GAD1/DRP-1.500	Gorelock1 with a DRP-1.500" (EFP, 3-A, Pro, Glidecam)	$485.00
Part# GAD1/DRM-1.580	Gorelock1 with a DRM-1.580" (Master, Ultra)	$485.00

New Style (Model 2) ( order this for all post sizes anticipating upgrading to a diffrent post size )

Part# GAD2/DR2-1.500	Gorelock2 with a DR2-1.500" (EFP, 3-A, Pro, Glidecam)	$485.00
Part# GAD2/DR2-1.580	Gorelock2 with a DR2-1.580" (Master, Ultra)	$485.00
Part# GAD2/DR2-2.00	Gorelock2 with a DR2-2.000" (Ultimate, MK-V, AR)	$485.00
Part# DR2	Docking Ring (call for I.D.sizes)	$85.00

Complete!

Part# GAD1/HDBP/DRP	Gorelock1 with HDBP and one DRP (Specify Size)	$975.00
Part# GAD2/HDBP/DR2	Gorelock2 with HDBP and one DR2 (Specify Size)	$975.00
Part# GAD2/HDBM/DR2	Gorelock2 with HDPM and one DR2 (Specify Size)	$975.00

Breakdown

+ =

Hill Docking Bracket^TM

The Hill Docking bracket that is user friendly.

Here you go Pro owners! Spin balance on the docking bracket. No more setting up the dolly or extinction arms. And 3A owners, no more turning the docking bracket around to balance the sled. Spin or static balance can be achieved of any sled with this new design. No more banging of the arm and the tools getting in the way when turning the docking bracket around as before, not to mention holding the rig and trying to do this at the same time. This docking bracket solves allot of the headaches.
To balance the sled simply undock from the Gorelock and pull the balancing post towards you and position the gimbal on the stud and spin or static balance. When done remove from stud and slide balancing post to the rear and dock the sled. The balancing post can be used to hang the vest when not in the balance mode.
The red knob is for setting the tension or drag on the balancing post. There are two C-stand receivers to choose from. The forward position will be used 90% of the time. The second position are those few times when you need more clearance between the stand and the sled, like low mode. (The balance post extends 12" inches from the stand and 15" inches when in the second C-stand receiver.) The arm stinger can be positioned from side to side by pushing up and over.(Spring loaded) The tool holder can be placed on either side of the docking bracket or can be removed all together, as you prefer. The extra holes can be used as a focus unit holder. (Not supplied with docking bracket) I will leave that up to you guys.
Also rock steady, no slop in movement of adjusting parts. Body is hard anodized black, balancing post is in hard anodize gray and the brake knob is red.Arm stinger and studs are 303 stainless steel. This is available in Pro / 3A / EFP & Master / Elite stud sizes.

Part#HDBP	Hill Docking bracket for Pro/3A (No Gorelock)	$500.00
Part#HDBM	Hill Docking bracket for Master/Elite (No Gorelock	$500.00

Mag-dock

Magliner docking support. This mounts to the 5/8" light stud that is on Magliner carts.
Pictured right is the GAD2 (Gorelock Auto Dock 2" Post) with stud receiver. The dock has a clearance of 5" from the cart so your sled will not hit. This has the same great features as the GAD2. Instead of using an old docking bracket this streamlines your cart and allows more space on the top shelf to work.
This is a stripped down version of the docking bracket. There are no balance studs, no arm hanger, and no adjustments, just docking. Now Available in the old style GAD1 (1.580" and 1.500" posts)

Great for moving to the next position. In the field, I move the sled and camera to the Mag-dock, (with the camera still attached) and push everything together. Your arms are around the sled pushing on the handles. I steady the sled when crossing cables, curbs, stairs, and rough surface.
Also can be used as a second dock stand for those long shots where you need a rest at the end of your shot.

Part #Mag-dock-1	Old Style 1.50"	$525.00
Part #Mag-dock-2	New Style 2.0"	$525.00

* Does not come with a docking ring. Sold as pictured above, top right.

PAM^TM "Preston Adjustable Motor Mount"

P.A.M. - Lighter, Better, Stronger, Easier, More Options, Cost Less!
The PAM mount allows owners of Preston motors to simplify operation.
The new PAM Mount takes advantage of the design of the motor and uses it to the operators benefit. As there is a hole that goes all the way through the motor (the mounting rod), a rosette is secured in the place of the rod. This allows the motor to be used on either side without going through the difficulty of changing the bracket setup. The PAM mount keeps the motor at a right angle to the lens at all times. PAM is positive locking, every 10 degrees to the lens over 360 degrees. The mount is also adjustable horizontally relative to the lens by 5" inches. Attaches to any standard iris rods. PAM is very quick and easy to use. The motor mount can stay built even when not in use. And best of all, the PAM Mount weighs just 3.4 ounces. (This is less than Preston's current swing arm.)
All PAM Mounts are hard anodized black.

The kits listed below include the Rosette,D-clamp and your choice of arm size.

PAM Mount w/15mm arm	Part #PAM-U-15mmKit	(Hill Rods & Arri)	$245.00
PAM Mount w/ 5/8" arm	Part #PAM-U-5/8"Kit	(Pana Rods)	$245.00
PAM Mount w/19mm arm	Part #PAM-U-19mmKit	(New Arri)	$245.00

For Scorpio motors order the kits below.

Pam Mount for Scorpio motor w/15mm arm	Part #Scorpio/Pam15mmKit	$265.00
Pam Mount for Scorpio motor w/5/8" arm	Part #Scorpio/Pam5/8"Kit	$265.00
Pam Mount for Scorpio motor w/19mm arm	Part #Scorpio/Pam19mmKit	$265.00

PAM Offset

The PAM Offset allows the motor to be offset by one or two inches depending on which way you position the motor. This replaces the arm clamp with a new clamp that has a one-inch standoff between the motor and the support arm. This allows you to get the motor into the Iris gear and around corners. This PAM Offset combined with the width of the motor will give you two inches offset.Takes seconds to install and requires no tools.

Part #PAMOFF

Weight: 1.58 oz

$85.00

Panavision Modular Motor Mount

This bracket inserts into the modular follow focus dovetail plate (MFFA) that is located directly under the lens. The Panavision modular mount replaces the manual focus knob with a Preston motor.

The Panavision modular plate (MFFA) is required to use this bracket.

The PMM-2 is a bracket that slides onto the Panavision modular follow focus dovetail mount.
The PMM-2 is supplied with two 15mm x 3" rods for motor placement.
The PAM bracket system will interface directly off the 15mm rods to drive focus, iris, zoom for most lenses.
This bracket is fully captive so you won't lose parts.

Part#PMM-2	$200.00
Part#PMM-2-6"Rod each	$36.00

NOTE: This longer replacement rod will work with the PMM-2 and Moviecam Com/SLSpud.(Below)

Movicam Compact/SL Iris stud

Iris Pull? This spud takes seconds to put on a Moviecam body. There is a small dovetail on the face of the camera, next to the lens. This simply slides onto that dovetail and a finger knob secures it. This can be used as a primary focus motor spud or a quick addition in the case of an Iris pull. Will work with both Compact and SL Bodies.
The stud is (15mm) 2 �" long and is Anodized Gray.

Part #MCom/SLSpud

Weight: 1.35 oz.

$100.00

Arri Iris Rod Clamp

This allows you to add an iris rod quick and easy. This Iris rod clamp inserts into the Arri dovetails. It works in combination with the Hill square to round rods. The clamp has two slots in the top of it for the rods to run horizontal or vertical (Depending on the camera). This will work on the following Arriflex camera's 535, 435, 35-3, SR-3, and any other cameras that have been modified with the Arri dovetail. The AIRC can be purchased alone by itself for those who own the rods already, and also with a rod as a kit. Comes as you see in the picture to the above left.

Part#AIRC	(Only)	$40.00
Part#AIRCSR35	(AIRC / SR-3.5" Rod)	$85.00
Part#AIRCSR5	(AIRC / SR-5" Rod)	$85.00
Part#AIRCSR7	(AIRC / SR-7" Rod)	$85.00

Arri SR-3 (Left)

Arri 35-3 (Right)

Movicam Compact/SL L.M.B.
Moviecam Compact/SL low mode bracket combo kit. Now a L.M.B. that will work on both bodies. Simple to install and lightweight. The kit includes one cheese plate and four standoff's. (Two for Compact and two for SL) Select the standoffs for the body that you are using and the cheese plate. The cheese plate has two counter bore slots for the square to round iris rods, for mounting lens motors. (Rods not included) The cheese plate can be adjusted fore and aft on the standoffs for center balance. All screws included. The L.M.B. can also be purchased as a dedicated bracket for each model separately.Camera courtesy of Rocky Mountain M.P. Rental. Weight: 10oz.

Part# #MCom/SL Combo L.M.B	$1,000.00
Part# #MCom L.M.B	$600.00
Part# #MSL-L.M.B	$600.00

Hill Handle
While shooting in low mode the live yoke is upside down and there is no place to hold the arm. The Hill Handle is a round tube that slips onto the arm post. It clamps around the arm post and is adjustable up and down and to any angle. This does not mar the post and takes a second to use. Makes low mode feel more comfortable to operate. (5/8" arm post only)
Weight: 1.35 oz.

Part#HH

$89.95

Dog bone 15mm to 19mm

This bracket allows you offset or adapt your motor mounting. One end has a 15mm clamp with a 3.5" long 15mm rod supplied. The other end has a 19mm clamp. This end will clamp onto a 19mm iris rod (new Arri) or can be used with my inserts to reduce down to the 5/8" ( Panavision ) or the 15mm (old Arri) iris rods. The Dog bone has a two-inch center-to-center spacing.

This is handy for getting the motor into those awkward places.

Part #Dogbone 15mm-19mm

(Dogbone 15mm-19mm with/15mm rod 3.5"L)

$75.00

Hill 2-N-1 Motor Mount

This is a motor rod for Arri cameras. It looks like a lollipop and screws into the rosette where the handle would go. The mating side of the Hill 2-N-1 is made of nylon so it conforms the rosette and will not move. The name 2-N-1 means that it has two uses. The mount can be taken apart so you have a square to round rod that will slip into the square access hole on the Arri BL's and the Arri 35-III handle.

Part #H21

Weight: 2.80 oz

$135.00

Square to Round Rods
These are different length rods for use with the #H21, #HP, #HLMB, #SR3Lmb, #SR3IVS, #AIRC. All rods are 15mm in diameter for motor placement. Lengths Available: 3.5", 5", 7" inch lengths.
Weight: 1.22 oz.

Part #SR3.5	3.5" square to round rod,	$45.00
Part #SR5	5" square to round rod,	$45.00
Part #SR7	7" square to round rod,	$45.00

Round Rods

#RR3.5	Round Rod 15mm x 3.5" Long	$20.00
#RR5	Round Rod 15mm x 5" Long	$20.00

Hill Pana Bracket

The Pana bracket mounts onto Panavision� cameras only.
This bracket allows up to 5 locations to mount rods. The bracket is very simple to install. It just slides onto the round accessory plug/matte box rod holder. This bracket is very strong and secure and will support any lens drive motor. Also will not interfere with low mode operation. (Rods sold separately)

Part #HP

Weight: 6.89 oz

$365.00

Hill Vehicle Mount
A Vehicle mount that mounts to a Mitchell top casting. Can be used with dolly, hi-hat, bazooka, Shotmaker. Also can be mounted to speed rail for motorcycle and auto shooting. Note: Vehicle Mount does not include the socket block. Socket block can be mounted on the right or left side. Comes supplied with U-bolts and screws.

(Sold in Blue only.)

Part #HVEL

$600.00

"Socket Block NLA"

Arm Post

Part #AP6	Arm Post ..... 6" Long
Part #AP8	Arm Post ..... 8" Long
Part #AP10	Arm Post .....10" Long
Part #AP12	Arm Post .....12" Long

Your choice $40.00 Each.

Arm Post Clamp

Arm post clamp for 5/8" post with thrust bearing for Pro, 3-A, EFP,Glidecam. Anodized Blue.

Part# APC

$25.00

Lens Control Raincover

You have made the investment now you need to protect it. This rain cover is large enough to work for several models. (Preston, BarTech, Scorpio, Fox, Seitz) It will also work with hardwire lens controls and will accommodate the addition of the Preston zoom control. The features include a clear cover, a neck strap, two arm inlets and velcro door with breathable fabric. It is rugged and lightweight yet will keep the moisture out.This will not interfere with the lens control signal. A must around salt water and works in snowy conditions as well.

Part #FIZRaincover

$ 85.00

StandBy Cover

The Hill StandBy cover is a must! This cover is great for location shooting when you need to protect your gear from the elements. This cover will guard against sun, dust, water, heat, people, or simply covering it to go to lunch or down time. Specially designed big enough to cover your entire rig. (The camera, sled, arm and vest) It is double stitched on the seams for added strength and water leaks. There are drawstrings at the bottom to synch it up to keep it from blowing off.

Can also be used for non-Steadicam use.(Hot Heads, Crane, Dolly, Vechile mounts, Etc.)
Will also work with the Steadicam in low mode position.

Supplied with a carrying pouch.
Not intended to be used while shooting.

Part #StandByCover.

$ 89.95

Steadicam Arm Protection Cover

Carabiner with a flash light in the end of it.Clip in on your belt or bag.
Useful when trying to find that certain thing in your bag.
I have also seen them on people's car keys. Batterie included."Purple"

H20 "on the go"

Tired of drinking someone elses water on the set. Do you write your name on the bottle only tofind out it has been misplaced or thrown away. Worse yet, is the set cluttered with bottles everywhere and a few even find there way into the shot.
Clip this bottle holder to your belt loop and never loose it again!

Ordering Information:

Accepting: American Express, Master Card and Visa credit cards.

When paying with Credit card please supply the following information with the order.

(Name on card,expiration date, billing address, phone number, and shipping address if different.)

Contact Jerry Hill directly via phone or fax, snail mail, and e-mail for more specific information concerning ordering. Shipping and handling charges additional, plus California residents add 9.75% sale tax. Prices are subject to change without notice.

Hill Products are made in the USA. Not responsible errors or omissions. All prices are in US dollars.
Feel free to print the full catalog below.

Shop Hours: Monday through Friday, 9am to 6pm - PST

Closed Weekends and Holidays!

Jerry Hill Steadicam Products
19160 Arminta Street
Reseda, Ca. 91335-1105
Phone -(818) 772-9256, Fax - (818) 772-9251
E-Mail: jerry@steadimoves.com

Back To The Top

HOME

To download our Catalog for Jerry Hill Steadicam Products
click DOWNLOAD NOW below.

The manual is in the Adobe Acrobat format (PDF), and should automatically
open for viewing/saving/printing.

If you don't have Acrobat on your computer,
click this button to download it free

DOWNLOAD NOW
(25 pages - 1.5 MB)

Price List only
(3 Pages)

©1997-2010, Jerry Hill. All rights reserved. Jerry-Rig, Gorelock1,Gorelock2,PAM,Uni-Clamp are trademarks of Jerry Hill.
Steadicam® is a tradmark of Tiffen Inc; Pack-it Sac® is a trademark of Eagle Creek Inc.

Part #Uni-Clamp (Above Left)	Weight: 2.80 oz.	$165.00
Part #PamUni-Clamp Kit (Center)	Weight: 4.44 oz.	$310.00
Part #Uni-ClampShaft 2.1/4"		$35.00
Part #Uni-ClampShaft 4.3/4"		$35.00

PAM 15mm arm	Part #Arm15mm	Hill, Arri	$100.00
PAM 5/8" arm	Part #Arm5/8"	Panavision	$100.00
PAM 19mm arm	Part #Arm19mm	New Arri, Red	$100.00
PAM 5/8" arm, (6" Long)	Part #PamArm5/8"L	Panavision	$100.00
PAM 19mm arm, (6" Long)	Part #PamArm19mmL	New Arri, Red	$100.00
Uni-Rosette for DM-1 & DM-2 Motor	Part #Pam Universal Rosette		$ 90.00
Scorpio to PAM bracket system	Part #ScorpioMount		$ 90.00
D-Clamp Replacement part	Part #PamDClamp		$ 85.00
Reducer 19mm to 15mm	Anodized Blue	Captive	$ 35.00
Reducer 19mm to 5/8	Anodized Red	Captive	$ 35.00
Adjustable Lever for arm's			$ 7.00

#PCS-4221	32 pitch x 1/2" wide output gear	$62.00
#PCS-4231	48 pitch gear (Panavision Zoom)	$52.00
#PCS-4232	64 pitch gear (Panavision Iris)	$52.00
#PCS-4240	.50M pitch gear (Cannon Video)	$52.00
#PCS-4241	60M pitch gear (Fuji,Focus, Zoom)	$52.00
#PCS-4242	.40M pitch gear (Fuji Iris)	$52.00
#EC-40041	Clip-On Neck Strap.	$10.95